| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: fix out-of-bounds write in l2cap_ecred_connect
l2cap_chan_connect() tries to ensure there are no more than
L2CAP_ECRED_CONN_SCID_MAX pending ECRED channels, so they fit in the
same L2CAP_ECRED_CONN_REQ that l2cap_ecred_connect() constructs.
However, the check only counts deferred channels. If 6 L2CAP sockets
are connected at the same time in order DDDDND (D=deferred,
N=non-deferred), the last can bump the total to max+1. It results to
one __le16 written out of bounds of the scid array, and an invalid
ECRED_CONN_REQ being sent.
Fix by leaving room for the non-deferred pending ECRED channels in the
counting in l2cap_chan_connect(), so the limit can't be exceeded.
Move counting under same critical section where the channel is added.
Although race conditions involving this appear unreachable, it's easier
to see.
Also add WARN_ON_ONCE check in l2cap_ecred_defer_connect() to make this
less brittle. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: initialize _md in vxlan_xmit_one()
If a VXLAN device is configured with both VXLAN_F_COLLECT_METADATA and
VXLAN_F_GBP, and a packet is transmitted through it using an external
ip_tunnel_info that lacks the IP_TUNNEL_VXLAN_OPT_BIT flag, md is left
pointing to the uninitialized _md stack variable:
if (test_bit(IP_TUNNEL_VXLAN_OPT_BIT, info->key.tun_flags)) {
if (info->options_len < sizeof(*md))
goto drop;
md = ip_tunnel_info_opts(info);
}
Because IP_TUNNEL_VXLAN_OPT_BIT is not set, md is not updated and remains
pointing to _md. Later, vxlan_build_skb() is called with md, which
eventually calls vxlan_build_gbp_hdr():
if (vxflags & VXLAN_F_GBP)
vxlan_build_gbp_hdr(vxh, md);
Inside vxlan_build_gbp_hdr(), md->gbp is read:
if (!md->gbp)
return;
gbp = (struct vxlanhdr_gbp *)vxh;
...
if (md->gbp & VXLAN_GBP_DONT_LEARN)
gbp->dont_learn = 1;
If the stack contains garbage, this causes:
1) VXLAN_HF_GBP flag to be spuriously set in the VXLAN header.
2) gbp->dont_learn and gbp->policy_applied to be set from stack bits.
3) gbp->policy_id to receive 16 bits of uninitialized kernel stack data,
leaking it onto the wire.
Fix this by zero-initializing _md. If IP_TUNNEL_VXLAN_OPT_BIT is not
present, md->gbp remains 0, and vxlan_build_gbp_hdr() returns early
without modifying the VXLAN header. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Prevent drain_pebs() reentry
The PEBS buffer is shared by all events on a CPU, so drain_pebs() must
not be reentered. If so, one instance may observe stale buffer state and
potentially access out-of-bound memory.
Most invocations happen in NMI context, which naturally prevents reentry.
However, drain_pebs() is also reachable from process context via
intel_pmu_drain_pebs_buffer().
In those paths, the PMU is often already disabled, but not guaranteed.
For example, __intel_pmu_pebs_disable() only disables the target counter,
so other active counters can still raise a PMI and interrupt an in-flight
drain_pebs(). Here is an example,
__perf_addr_filters_adjust()
perf_event_stop()
__perf_event_stop()
x86_pmu_stop() (event->pmu->stop)
intel_pmu_disable_event()
intel_pmu_pebs_disable()
__intel_pmu_pebs_disable()
intel_pmu_drain_large_pebs()
intel_pmu_drain_pebs_buffer()
Introduce __intel_pmu_quiesce() and __intel_pmu_resume() helpers and
use them in intel_pmu_drain_large_pebs() to disable the full PMU
around the intel_pmu_drain_pebs_buffer() call, preventing reentry.
Also add a warning in intel_pmu_drain_pebs_buffer() when the full PMU is
not disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix TX descriptor availability check for TSO traffic
stmmac_tso_xmit() estimates the number of free TX descriptors required by
a TSO skb as:
(skb->len - proto_hdr_len) / TSO_MAX_BUFF_SIZE + 1
which assumes the payload is split into TSO_MAX_BUFF_SIZE chunks. This
underestimates the descriptors actually consumed by stmmac_tso_allocator(),
since each fragment is mapped individually and so it needs at least one
descriptor regardless of its size. Moreover, one descriptor is used for
the L2/L3/L4 headers and, when the MSS changes, one more is consumed for
the MSS context descriptor.
For a highly fragmented TSO skb the check can therefore pass even when the
ring has too few free slots. stmmac_tso_allocator() then writes past the
available descriptors, overwriting descriptors still owned by the DMA
engine, corrupting the TX ring.
Add stmmac_tso_get_num_desc() to compute the exact number of descriptors
needed for the header, the linear payload and each fragment, plus the MSS
context descriptor when required, and use it in the availability check. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix memory corruption from a "STACKTRACE" histogram key
"cpu", "CPU", "stacktrace" and "STACKTRACE" are generic fields, defined
with an offset and a size of zero so that the filter code can match them
by name. parse_field() maps them onto their common_* equivalents for
backward compatibility, but unlike the common_* names it hands the
placeholder back to the caller instead of NULL.
create_hist_field() takes a non-NULL field as a promise that the record
carries a stacktrace and picks HIST_FIELD_FN_STACK, so the __data_loc
word is read from offset 0, that is from common_type, and its low 16
bits are followed as an offset into the record. What is found there
becomes the length of an unbounded memcpy. Pick an event whose id is
small enough that the offset stays inside its own record and the length
is a kernel text address:
# cd /sys/kernel/tracing
# echo 'hist:keys=STACKTRACE' > events/ftrace/print/trigger
# echo hello > trace_marker
Oops: general protection fault, probably for non-canonical address
RIP: 0010:rb_next+0x23/0x60
</IRQ>
RIP: 0010:memcpy+0xc/0x30
event_hist_trigger+0x2e7/0x12c0
Kernel panic - not syncing: Fatal exception in interrupt
Leave the field NULL, which is what the comment above the branch says
the code does and what common_stacktrace already does. FILTER_CPU and
FILTER_COMM are left alone, their create_hist_field() branches never
look at the field. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Validate full buffer range in ivpu_to_cpu_addr
Add a size parameter to ivpu_to_cpu_addr() and validate that the
whole [vpu_addr, vpu_addr + size) range stays within the BO. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Validate firmware log buffer metadata
The tracing log headers parsed by fw_log_print_buffer() reside in
DMA-shared BOs that the NPU firmware can write to.
fw_log_from_bo() validated log->header_size and log->size, but
fw_log_print_buffer() re-read those same fields from shared memory
afterwards, allowing a TOCTOU where firmware changes them between the
check and the use, and making the host dereference out-of-bounds
addresses while printing logs.
Snapshot the validated values once with READ_ONCE() and pass them down
explicitly in a new struct ivpu_fw_log_desc instead of re-reading them
from the shared struct. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Bound VP index against VP_CTRL IOCB bitmap size
The VP control IOCB selects its target virtual port by setting one bit
in vp_idx_map, a fixed 16-byte (128-bit) array in both
vp_ctrl_entry_24xx and vp_ctrl_entry_24xx_ext. qla25xx_ctrlvp_iocb()
computes map = (vp_index - 1) / 8 and writes vce->vp_idx_map[map]
without checking that map stays within the array.
max_npiv_vports is taken from firmware and only sanitized to a
MIN_MULTI_ID_FABRIC-aligned boundary, so it can legitimately be 191 or
255, and qla24xx_control_vp() only rejects vp_index >= max_npiv_vports.
A vp_index above 128 therefore yields map >= 16 and an out-of-bounds
write of up to 16 bytes past vp_idx_map, corrupting the trailing IOCB
fields (or the adjacent request-ring slot on the 64-byte layout).
Reject a vp_index that cannot be represented in the IOCB bitmap in
qla24xx_control_vp(), and add a defensive ARRAY_SIZE() guard in
qla25xx_ctrlvp_iocb() before the write. Adapters that report the usual
63 or 127 NPIV vports are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: reject duplicate wiphy cipher suite entries
Duplicate entries in wiphy->cipher_suites do not describe any
additional capability, but cfg80211 currently accepts them and leaves
individual consumers to deal with them.
One such consumer is the WEXT compatibility code, which appends a WEP
key length for each WEP cipher entry it sees. Repeated WEP entries can
therefore overflow the fixed iw_range::encoding_size array returned by
SIOCGIWRANGE.
Reject duplicate cipher suite entries in wiphy_register() instead.
This keeps the cipher suite invariant in one place and makes malformed
wiphy descriptions fail early with -EINVAL, rather than relying on a
single cfg80211 user to handle duplicates correctly. |
| In the Linux kernel, the following vulnerability has been resolved:
genirq/proc: Size interrupt directory names for 10-digit interrupt numbers
/proc/irq/<n>/ directory names are built in `char name[10]` buffers
with `sprintf(name, "%u", irq)`.
Ten-digit IRQ numbers already need 11 bytes including the trailing NUL, and
current sparse-IRQ configurations allow interrupt numbers in that range.
Size the temporary name buffer for the current decimal form and switch
to bounded formatting when creating or removing the proc entry. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: validate and share PSP fw_pri_buf copies via psp_copy_fw
Change psp_copy_fw from void to int: return -ENODEV when drm_dev_enter
fails, and -EINVAL when the image size is zero or larger than the
1 MiB PSP private buffer.
Replace open-coded memset/memcpy into fw_pri_buf with psp_copy_fw. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Bound GPIO I2C table entry count from VBIOS
Reject undersized tables and cap the derived entry count
to AMDGPU_MAX_I2C_BUS so we do not overrun adev->i2c_bus[]
or walk an absurd number of entries on corrupt size fields. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Zero queue and stack outputs on lock failure
Queue and stack pop/peek helpers accept an uninitialized output buffer
because the verifier expects the helper to initialize it. The empty-map
error path clears the buffer, but a failed lock acquisition returns
-EBUSY without writing it.
Clear the output before returning -EBUSY so BPF programs cannot observe
uninitialized stack contents after a failed helper call. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: validate RX band_idx before dereferencing phys[]
band_idx comes from a 2-bit descriptor field (0-3) and was used directly
to index dev->mt76.phys[] (size __MT_MAX_BAND == 3) and dereference the
result. A corrupt or reserved descriptor value could index out of bounds
or hit a NULL phy on parts with fewer bands. Reject invalid band indices,
mirroring mt7996_rx_get_wcid(). |
| In the Linux kernel, the following vulnerability has been resolved:
blk-cgroup: fix race between policy activation and blkg destruction
When switching an IO scheduler on a block device, blkcg_activate_policy()
allocates blkg_policy_data (pd) for all blkgs attached to the queue.
However, blkcg_activate_policy() may race with concurrent blkcg deletion,
leading to use-after-free and memory leak issues.
The use-after-free occurs in the following race:
T1 (blkcg_activate_policy):
- Successfully allocates pd for blkg1 (loop0->queue, blkcgA)
- Fails to allocate pd for blkg2 (loop0->queue, blkcgB)
- Enters the enomem rollback path to release blkg1 resources
T2 (blkcg deletion):
- blkcgA is deleted concurrently
- blkg1 is freed via blkg_free_workfn()
- blkg1->pd is freed
T1 (continued):
- Rollback path accesses blkg1->pd->online after pd is freed
- Triggers use-after-free
In addition, blkg_free_workfn() frees pd before removing the blkg from
q->blkg_list. This allows blkcg_activate_policy() to allocate a new pd
for a blkg that is being destroyed, leaving the newly allocated pd
unreachable when the blkg is finally freed.
Fix these races by extending blkcg_mutex coverage to serialize
blkcg_activate_policy() rollback and blkg destruction, ensuring pd
lifecycle is synchronized with blkg list visibility. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: fix max_qid race between configfs and controller allocation
The function nvmet_subsys_attr_qid_max_store() can race against
nvmet_alloc_ctrl() when a subsystem's max_qid limit is modified.
Suppose max_qid is currently 64. If nvmet_alloc_ctrl() executes:
ctrl->sqs = kzalloc_objs(struct nvmet_sq *, subsys->max_qid + 1);
and at this exact point, a userspace process changes max_qid to 128,
nvmet_subsys_attr_qid_max_store() will set the new max_qid value. It
attempts to delete active controllers to force a reconnect, but the
new controller won't be deleted because it hasn't been added to the
subsys->ctrls list yet.
nvmet_alloc_ctrl() then proceeds and adds the new controller to the
subsys->ctrls list. Later, when nvmet_install_queue() is called, it
will see max_qid set to 128, but the memory allocated for sqs is only
sized for 64 entries. This results in a KASAN out-of-bounds warning
and potential memory corruptions.
Fix this by protecting the queue allocations and list insertion in
nvmet_alloc_ctrl() with down_read(&nvmet_config_sem). Because
nvmet_subsys_attr_qid_max_store() acquires down_write(&nvmet_config_sem)
to modify the attribute, this safely prevents the configfs writer from
modifying max_qid during controller creation.
Copy the max_qid from the subsystem to the controller's structure
during the allocation; ctrl->max_qid never changes as long as the
controller remains in LIVE state, so this will prevent similar race
conditions. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Fix memory corruption by not reinjecting CK machine checks
Channel-subsystem damage machine checks are for the host channel
subsystem. The guest channel subsystem is emulated in the userspace VMM.
There is no point in forwarding such machine checks into the guest.
This also simplifies the machine check reinjection and avoids kfree of a
stack variable as reported by sashiko. There might be still machine
checks that have the ck bit set with another bit (like instruction
damage), mask out the CK bit in s390_backup_mcck_info(), like the CP and
ED bits already are. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to migrate all curseg types during free_segment_range
In free_segment_range(), the curseg evacuation loop only iterates up to
NR_CURSEG_PERSIST_TYPE (0..5), missing non-persistent in-memory curseg
types such as CURSEG_COLD_DATA_PINNED and CURSEG_ALL_DATA_ATGC.
Even though these in-memory curseg types are not saved in the on-disk
checkpoint header, they still occupy active physical segments at runtime.
If an active in-memory curseg happens to be allocated within the segment
range being truncated during filesystem shrink, failing to evacuate it
will cause subsequent writes to the curseg attempting out-of-bounds I/O
on the truncated storage range.
Fix this by expanding the curseg evacuation loop upper bound to
NR_CURSEG_TYPE to ensure all active curseg types are safely migrated
out of the target range. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: fix out-of-bounds write when null terminating a label vec
aa_vec_unique() null terminates at vec[n - dups] when VEC_FLAG_TERMINATE
is passed. If the components are all distinct no duplicates are dropped,
dups is 0 and the terminator goes to vec[n], so the caller has to provide
room for n + 1 entries.
aa_label_strn_parse() sets up its vector with vec_setup(profile, vec, len,
gfp) and then calls aa_vec_unique(vec, len, VEC_FLAG_TERMINATE), but
vec_setup() does not reserve the terminator entry. Up to LOCAL_VEC_ENTRIES
it uses the local array of LOCAL_VEC_ENTRIES pointers, above that it
allocates exactly len pointers. The terminator therefore lands one entry
past the end of the local array when len is LOCAL_VEC_ENTRIES, and one
entry past the end of the allocation when len is larger.
len comes from the number of "//&" separated components in the label name
and label_count_strn_entries() does not bound it. An unprivileged task
reaches the parse by writing to /proc/self/attr/apparmor/current or through
lsm_set_self_attr(2), both of which go through do_setattr(), and the name
is parsed before the change_profile permission is checked.
The query_label() path behind the securityfs .access file, which is
mode 0666, performs no permission check at all. Every component has to
resolve to a loaded profile, so a system with policy loaded is required.
The other two VEC_FLAG_TERMINATE users work on a label vec that
aa_label_alloc() has already sized with "+ 1 for null terminator entry on
vec". Reserve the same entry in vec_setup() and DEFINE_VEC(). Passing
len + 1 from the caller instead would move len == LOCAL_VEC_ENTRIES out of
the local array and into kzalloc(). |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus) Fix type confusion in notification logic
Sashiko reports:
At the start of the loop in pmbus_notify(), the code unconditionally casts
every attribute to a struct sensor_device_attribute:
drivers/hwmon/pmbus/pmbus_core.c:pmbus_notify() {
for (i = 0; i < data->num_attributes; i++) {
struct device_attribute *da = to_dev_attr(data->group.attrs[i]);
struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
int index = attr->index;
...
}
However, data->group.attrs can contain other types like struct
pmbus_samples_reg or struct pmbus_sensor, which only embed a base
struct device_attribute.
If da is a struct pmbus_samples_reg, dev_attr is the last member. Casting
it to struct sensor_device_attribute and reading the index field appears
to access memory past the end of the allocation, which might trigger a
slab-out-of-bounds read.
Additionally, if da is a struct pmbus_sensor, casting it causes the index
field to overlap with the page, phase, and reg fields. Could this produce
a garbage mask on little-endian systems that spuriously matches the target
reg, page, and flags during an alert?
Fix the problem by using struct sensor_device_attr in struct pmbus_sensor
and struct pmbus_label. Since those attributes never trigger a
notification, set the value of attr->index to -1 for them. Use this value
to distinguish from boolean attributes which _can_ trigger a notification
and use the index field to encode mask, page, and register values. |
