| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/userq: fix access to stale wptr mapping
Use drm_exec to take both locks i.e vm root bo and
wptr_obj bo to access the mapping data properly.
This fixes the security issue of unmap the wptr_obj while
a queue creation is in progress and passing other
bo at same address.
(cherry picked from commit 1fc6c8ab45dbee096469c08c13f6099d57a52d6c) |
| In the Linux kernel, the following vulnerability has been resolved:
flow_dissector: do not dissect PPPoE PFC frames
RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT
RECOMMENDED for PPPoE. In practice, pppd does not support negotiating
PFC for PPPoE sessions, and the flow dissector driver has assumed an
uncompressed frame until the blamed commit.
During the review process of that commit [1], support for PFC is
suggested. However, having a compressed (1-byte) protocol field means
the subsequent PPP payload is shifted by one byte, causing 4-byte
misalignment for the network header and an unaligned access exception
on some architectures.
The exception can be reproduced by sending a PPPoE PFC frame to an
ethernet interface of a MIPS board, with RPS enabled, even if no PPPoE
session is active on that interface:
$ 0 : 00000000 80c40000 00000000 85144817
$ 4 : 00000008 00000100 80a75758 81dc9bb8
$ 8 : 00000010 8087ae2c 0000003d 00000000
$12 : 000000e0 00000039 00000000 00000000
$16 : 85043240 80a75758 81dc9bb8 00006488
$20 : 0000002f 00000007 85144810 80a70000
$24 : 81d1bda0 00000000
$28 : 81dc8000 81dc9aa8 00000000 805ead08
Hi : 00009d51
Lo : 2163358a
epc : 805e91f0 __skb_flow_dissect+0x1b0/0x1b50
ra : 805ead08 __skb_get_hash_net+0x74/0x12c
Status: 11000403 KERNEL EXL IE
Cause : 40800010 (ExcCode 04)
BadVA : 85144817
PrId : 0001992f (MIPS 1004Kc)
Call Trace:
[<805e91f0>] __skb_flow_dissect+0x1b0/0x1b50
[<805ead08>] __skb_get_hash_net+0x74/0x12c
[<805ef330>] get_rps_cpu+0x1b8/0x3fc
[<805fca70>] netif_receive_skb_list_internal+0x324/0x364
[<805fd120>] napi_complete_done+0x68/0x2a4
[<8058de5c>] mtk_napi_rx+0x228/0xfec
[<805fd398>] __napi_poll+0x3c/0x1c4
[<805fd754>] napi_threaded_poll_loop+0x234/0x29c
[<805fd848>] napi_threaded_poll+0x8c/0xb0
[<80053544>] kthread+0x104/0x12c
[<80002bd8>] ret_from_kernel_thread+0x14/0x1c
Code: 02d51821 1060045b 00000000 <8c640000> 3084000f 2c820005 144001a2 00042080 8e220000
To reduce the attack surface and maintain performance, do not process
PPPoE PFC frames.
[1] https://lore.kernel.org/r/20220630231016.GA392@debian.home |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: avoid recursive nvmet-wq flush in nvmet_ctrl_free
nvmet_tcp_release_queue_work() runs on nvmet-wq and can drop the
final controller reference through nvmet_cq_put(). If that triggers
nvmet_ctrl_free(), the teardown path flushes ctrl->async_event_work on
the same nvmet-wq.
Call chain:
nvmet_tcp_schedule_release_queue()
kref_put(&queue->kref, nvmet_tcp_release_queue)
nvmet_tcp_release_queue()
queue_work(nvmet_wq, &queue->release_work) <--- nvmet_wq
process_one_work()
nvmet_tcp_release_queue_work()
nvmet_cq_put(&queue->nvme_cq)
nvmet_cq_destroy()
nvmet_ctrl_put(cq->ctrl)
nvmet_ctrl_free()
flush_work(&ctrl->async_event_work) <--- nvmet_wq
Previously Scheduled by :-
nvmet_add_async_event
queue_work(nvmet_wq, &ctrl->async_event_work);
This trips lockdep with a possible recursive locking warning.
[ 5223.015876] run blktests nvme/003 at 2026-04-07 20:53:55
[ 5223.061801] loop0: detected capacity change from 0 to 2097152
[ 5223.072206] nvmet: adding nsid 1 to subsystem blktests-subsystem-1
[ 5223.088368] nvmet_tcp: enabling port 0 (127.0.0.1:4420)
[ 5223.126086] nvmet: Created discovery controller 1 for subsystem nqn.2014-08.org.nvmexpress.discovery for NQN nqn.2014-08.org.nvmexpress:uuid:0f01fb42-9f7f-4856-b0b3-51e60b8de349.
[ 5223.128453] nvme nvme1: new ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery", addr 127.0.0.1:4420, hostnqn: nqn.2014-08.org.nvmexpress:uuid:0f01fb42-9f7f-4856-b0b3-51e60b8de349
[ 5233.199447] nvme nvme1: Removing ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery"
[ 5233.227718] ============================================
[ 5233.231283] WARNING: possible recursive locking detected
[ 5233.234696] 7.0.0-rc3nvme+ #20 Tainted: G O N
[ 5233.238434] --------------------------------------------
[ 5233.241852] kworker/u192:6/2413 is trying to acquire lock:
[ 5233.245429] ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: touch_wq_lockdep_map+0x26/0x90
[ 5233.251438]
but task is already holding lock:
[ 5233.255254] ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x5cc/0x6e0
[ 5233.261125]
other info that might help us debug this:
[ 5233.265333] Possible unsafe locking scenario:
[ 5233.269217] CPU0
[ 5233.270795] ----
[ 5233.272436] lock((wq_completion)nvmet-wq);
[ 5233.275241] lock((wq_completion)nvmet-wq);
[ 5233.278020]
*** DEADLOCK ***
[ 5233.281793] May be due to missing lock nesting notation
[ 5233.286195] 3 locks held by kworker/u192:6/2413:
[ 5233.289192] #0: ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x5cc/0x6e0
[ 5233.294569] #1: ffffc9000e2a7e40 ((work_completion)(&queue->release_work)){+.+.}-{0:0}, at: process_one_work+0x1c5/0x6e0
[ 5233.300128] #2: ffffffff82d7dc40 (rcu_read_lock){....}-{1:3}, at: __flush_work+0x62/0x530
[ 5233.304290]
stack backtrace:
[ 5233.306520] CPU: 4 UID: 0 PID: 2413 Comm: kworker/u192:6 Tainted: G O N 7.0.0-rc3nvme+ #20 PREEMPT(full)
[ 5233.306524] Tainted: [O]=OOT_MODULE, [N]=TEST
[ 5233.306525] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014
[ 5233.306527] Workqueue: nvmet-wq nvmet_tcp_release_queue_work [nvmet_tcp]
[ 5233.306532] Call Trace:
[ 5233.306534] <TASK>
[ 5233.306536] dump_stack_lvl+0x73/0xb0
[ 5233.306552] print_deadlock_bug+0x225/0x2f0
[ 5233.306556] __lock_acquire+0x13f0/0x2290
[ 5233.306563] lock_acquire+0xd0/0x300
[ 5233.306565] ? touch_wq_lockdep_map+0x26/0x90
[ 5233.306571] ? __flush_work+0x20b/0x530
[ 5233.306573] ? touch_wq_lockdep_map+0x26/0x90
[ 5233.306577] touch_wq_lockdep_map+0x3b/0x90
[ 5233.306580] ? touch_wq_lockdep_map+0x26/0x90
[ 52
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: do WoW offloads only on primary link
In case of multi-link connection, WCN7850 firmware crashes due to WoW
offloads enabled on both primary and secondary links.
Change to do it only on primary link to fix it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
procfs: fix missing RCU protection when reading real_parent in do_task_stat()
When reading /proc/[pid]/stat, do_task_stat() accesses task->real_parent
without proper RCU protection, which leads to:
cpu 0 cpu 1
----- -----
do_task_stat
var = task->real_parent
release_task
call_rcu(delayed_put_task_struct)
task_tgid_nr_ns(var)
rcu_read_lock <--- Too late to protect task->real_parent!
task_pid_ptr <--- UAF!
rcu_read_unlock
This patch uses task_ppid_nr_ns() instead of task_tgid_nr_ns() to add
proper RCU protection for accessing task->real_parent. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_inner: Fix IPv6 inner_thoff desync
In nft_inner_parse_l2l3(), when processing inner IPv6 packets,
ipv6_find_hdr() correctly computes the transport header offset
traversing all extension headers, but the result is immediately
overwritten with nhoff + sizeof(_ip6h) (40 bytes), which only
accounts for the IPv6 base header. This creates a desync between
inner_thoff (wrong — points to extension header start) and l4proto
(correct — e.g., IPPROTO_TCP), enabling transport header forgery
and potential firewall bypass. This issue affects stable versions
from Linux 6.2.
For comparison, the normal (non-inner) IPv6 path correctly
preserves ipv6_find_hdr()'s result. Removing the incorrect overwrite
ensures that ipv6_find_hdr()'s calculated transport header offset is
preserved, thereby fixing the desynchronization. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/CPU/AMD: Prevent improper isolation of shared resources in Zen2's op cache
Make sure resources are not improperly shared in the op cache and
cause instruction corruption this way. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: drop stray 'static' from fast-RX rx_result
ieee80211_invoke_fast_rx() is documented as safe for parallel RX, but
its per-invocation rx_result is declared static. Concurrent callers then
share one instance and can overwrite each other's result between
ieee80211_rx_mesh_data() and the switch on res.
That can make a packet that was queued or consumed by
ieee80211_rx_mesh_data() fall through into ieee80211_rx_8023(), or make
a packet that should continue return as queued.
Make res an automatic variable so each invocation keeps its own result. |
| In the Linux kernel, the following vulnerability has been resolved:
fanotify: fix false positive on permission events
fsnotify_get_mark_safe() may return false for a mark on an unrelated group,
which results in bypassing the permission check.
Fix by skipping over detached marks that are not in the current group. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/mana: Validate rx_hash_key_len
Sashiko points out that rx_hash_key_len comes from a uAPI structure and is
blindly passed to memcpy, allowing the userspace to trash kernel
memory. Bounds check it so the memcpy cannot overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
isofs: validate block number from NFS file handle in isofs_export_iget
isofs_fh_to_dentry() and isofs_fh_to_parent() pass an attacker-
controlled block number (ifid->block or ifid->parent_block) from
the NFS file handle to isofs_export_iget(), which only rejects
block == 0 before calling isofs_iget() and ultimately sb_bread().
A crafted file handle with fh_len sufficient to pass the check
added by commit 0405d4b63d08 ("isofs: Prevent the use of too small
fid") can still drive the server to read any in-range block on the
backing device as if it were an iso_directory_record. That earlier
fix was assigned CVE-2025-37780.
sb_bread() on an out-of-range block returns NULL cleanly via the
EIO path, so there is no memory-safety violation. For in-range
reads of adjacent-partition data on the same block device, the
unrelated bytes end up in iso_inode_info fields that reach the NFS
client as dentry metadata. The deployment surface (isofs exported
over NFS from loop-mounted images) is narrow and requires an
authenticated NFS peer, but the malformed-file-handle class is
reportable as hardening next to the existing CVE-2025-37780 fix.
Reject block >= ISOFS_SB(sb)->s_nzones in isofs_export_iget() so
the check covers both isofs_fh_to_dentry() and isofs_fh_to_parent()
call sites with a single line. |
| In the Linux kernel, the following vulnerability has been resolved:
block: add pgmap check to biovec_phys_mergeable
biovec_phys_mergeable() is used by the request merge, DMA mapping,
and integrity merge paths to decide if two physically contiguous
bvec segments can be coalesced into one. It currently has no check
for whether the segments belong to different dev_pagemaps.
When zone device memory is registered in multiple chunks, each chunk
gets its own dev_pagemap. A single bio can legitimately contain
bvecs from different pgmaps -- iov_iter_extract_bvecs() breaks at
pgmap boundaries but the outer loop in bio_iov_iter_get_pages()
continues filling the same bio. If such bvecs are physically
contiguous, biovec_phys_mergeable() will coalesce them, making it
impossible to recover the correct pgmap for the merged segment
via page_pgmap().
Add a zone_device_pages_have_same_pgmap() check to prevent merging
bvec segments that span different pgmaps. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipv6: fix NOREF dst use in seg6 and rpl lwtunnels
seg6_input_core() and rpl_input() call ip6_route_input() which sets a
NOREF dst on the skb, then pass it to dst_cache_set_ip6() invoking
dst_hold() unconditionally.
On PREEMPT_RT, ksoftirqd is preemptible and a higher-priority task can
release the underlying pcpu_rt between the lookup and the caching
through a concurrent FIB lookup on a shared nexthop.
Simplified race sequence:
ksoftirqd/X higher-prio task (same CPU X)
----------- --------------------------------
seg6_input_core(,skb)/rpl_input(skb)
dst_cache_get()
-> miss
ip6_route_input(skb)
-> ip6_pol_route(,skb,flags)
[RT6_LOOKUP_F_DST_NOREF in flags]
-> FIB lookup resolves fib6_nh
[nhid=N route]
-> rt6_make_pcpu_route()
[creates pcpu_rt, refcount=1]
pcpu_rt->sernum = fib6_sernum
[fib6_sernum=W]
-> cmpxchg(fib6_nh.rt6i_pcpu,
NULL, pcpu_rt)
[slot was empty, store succeeds]
-> skb_dst_set_noref(skb, dst)
[dst is pcpu_rt, refcount still 1]
rt_genid_bump_ipv6()
-> bumps fib6_sernum
[fib6_sernum from W to Z]
ip6_route_output()
-> ip6_pol_route()
-> FIB lookup resolves fib6_nh
[nhid=N]
-> rt6_get_pcpu_route()
pcpu_rt->sernum != fib6_sernum
[W <> Z, stale]
-> prev = xchg(rt6i_pcpu, NULL)
-> dst_release(prev)
[prev is pcpu_rt,
refcount 1->0, dead]
dst = skb_dst(skb)
[dst is the dead pcpu_rt]
dst_cache_set_ip6(dst)
-> dst_hold() on dead dst
-> WARN / use-after-free
For the race to occur, ksoftirqd must be preemptible (PREEMPT_RT without
PREEMPT_RT_NEEDS_BH_LOCK) and a concurrent task must be able to release
the pcpu_rt. Shared nexthop objects provide such a path, as two routes
pointing to the same nhid share the same fib6_nh and its rt6i_pcpu
entry.
Fix seg6_input_core() and rpl_input() by calling skb_dst_force() after
ip6_route_input() to force the NOREF dst into a refcounted one before
caching.
The output path is not affected as ip6_route_output() already returns a
refcounted dst. |
| In the Linux kernel, the following vulnerability has been resolved:
selinux: fix overlayfs mmap() and mprotect() access checks
The existing SELinux security model for overlayfs is to allow access if
the current task is able to access the top level file (the "user" file)
and the mounter's credentials are sufficient to access the lower
level file (the "backing" file). Unfortunately, the current code does
not properly enforce these access controls for both mmap() and mprotect()
operations on overlayfs filesystems.
This patch makes use of the newly created security_mmap_backing_file()
LSM hook to provide the missing backing file enforcement for mmap()
operations, and leverages the backing file API and new LSM blob to
provide the necessary information to properly enforce the mprotect()
access controls. |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: only d_add() negative dentries when they are unhashed
Ceph can call d_add(dentry, NULL) on a negative dentry that is already
present in the primary dcache hash.
In the current VFS that is not safe. d_add() goes through __d_add()
to __d_rehash(), which unconditionally reinserts dentry->d_hash into
the hlist_bl bucket. If the dentry is already hashed, reinserting the
same node can corrupt the bucket, including creating a self-loop.
Once that happens, __d_lookup() can spin forever in the hlist_bl walk,
typically looping only on the d_name.hash mismatch check and
eventually triggering RCU stall reports like this one:
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 87-....: (2100 ticks this GP) idle=3a4c/1/0x4000000000000000 softirq=25003319/25003319 fqs=829
rcu: (t=2101 jiffies g=79058445 q=698988 ncpus=192)
CPU: 87 UID: 2952868916 PID: 3933303 Comm: php-cgi8.3 Not tainted 6.18.17-i1-amd #950 NONE
Hardware name: Dell Inc. PowerEdge R7615/0G9DHV, BIOS 1.6.6 09/22/2023
RIP: 0010:__d_lookup+0x46/0xb0
Code: c1 e8 07 48 8d 04 c2 48 8b 00 49 89 fc 49 89 f5 48 89 c3 48 83 e3 fe 48 83 f8 01 77 0f eb 2d 0f 1f 44 00 00 48 8b 1b 48 85 db <74> 20 39 6b 18 75 f3 48 8d 7b 78 e8 ba 85 d0 00 4c 39 63 10 74 1f
RSP: 0018:ff745a70c8253898 EFLAGS: 00000282
RAX: ff26e470054cb208 RBX: ff26e470054cb208 RCX: 000000006e958966
RDX: ff26e48267340000 RSI: ff745a70c82539b0 RDI: ff26e458f74655c0
RBP: 000000006e958966 R08: 0000000000000180 R09: 9cd08d909b919a89
R10: ff26e458f74655c0 R11: 0000000000000000 R12: ff26e458f74655c0
R13: ff745a70c82539b0 R14: d0d0d0d0d0d0d0d0 R15: 2f2f2f2f2f2f2f2f
FS: 00007f5770896980(0000) GS:ff26e482c5d88000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f5764de50c0 CR3: 000000a72abb5001 CR4: 0000000000771ef0
PKRU: 55555554
Call Trace:
<TASK>
lookup_fast+0x9f/0x100
walk_component+0x1f/0x150
link_path_walk+0x20e/0x3d0
path_lookupat+0x68/0x180
filename_lookup+0xdc/0x1e0
vfs_statx+0x6c/0x140
vfs_fstatat+0x67/0xa0
__do_sys_newfstatat+0x24/0x60
do_syscall_64+0x6a/0x230
entry_SYSCALL_64_after_hwframe+0x76/0x7e
This is reachable with reused cached negative dentries. A Ceph lookup
or atomic_open can be handed a negative dentry that is already hashed,
and fs/ceph/dir.c then hits one of two paths that incorrectly assume
"negative" also means "unhashed":
- ceph_finish_lookup():
MDS reply is -ENOENT with no trace
-> d_add(dentry, NULL)
- ceph_lookup():
local ENOENT fast path for a complete directory with shared caps
-> d_add(dentry, NULL)
Both paths can therefore re-add an already-hashed negative dentry.
Ceph already uses the correct pattern elsewhere: ceph_fill_trace() only
calls d_add(dn, NULL) for a negative null-dentry reply when d_unhashed(dn)
is true.
Fix both fs/ceph/dir.c sites the same way: only call d_add() for a
negative dentry when it is actually unhashed. If the negative dentry
is already hashed, leave it in place and reuse it as-is.
This preserves the existing behavior for unhashed dentries while
avoiding d_hash list corruption for reused hashed negatives. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Validate pad and ICRC before payload_size() in rxe_rcv
rxe_rcv() currently checks only that the incoming packet is at least
header_size(pkt) bytes long before payload_size() is used.
However, payload_size() subtracts both the attacker-controlled BTH pad
field and RXE_ICRC_SIZE from pkt->paylen:
payload_size = pkt->paylen - offset[RXE_PAYLOAD] - bth_pad(pkt)
- RXE_ICRC_SIZE
This means a short packet can still make payload_size() underflow even
if it includes enough bytes for the fixed headers. Simply requiring
header_size(pkt) + RXE_ICRC_SIZE is not sufficient either, because a
packet with a forged non-zero BTH pad can still leave payload_size()
negative and pass an underflowed value to later receive-path users.
Fix this by validating pkt->paylen against the full minimum length
required by payload_size(): header_size(pkt) + bth_pad(pkt) +
RXE_ICRC_SIZE. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: icmp: validate reply type before using icmp_pointers
Extended echo replies use ICMP_EXT_ECHOREPLY as the outbound reply type.
That value is outside the range covered by icmp_pointers[], which only
describes the traditional ICMP types up to NR_ICMP_TYPES.
Avoid consulting icmp_pointers[] for reply types outside that range, and
use array_index_nospec() for the remaining in-range lookup. Normal ICMP
replies keep their existing behavior unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: avoid early lgr access in smc_clc_wait_msg
A CLC decline can be received while the handshake is still in an early
stage, before the connection has been associated with a link group.
The decline handling in smc_clc_wait_msg() updates link-group level sync
state for first-contact declines, but that state only exists after link
group setup has completed. Guard the link-group update accordingly and
keep the per-socket peer diagnosis handling unchanged.
This preserves the existing sync_err handling for established link-group
contexts and avoids touching link-group state before it is available. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: call sk_data_ready() after listener migration
When inet_csk_listen_stop() migrates an established child socket from
a closing listener to another socket in the same SO_REUSEPORT group,
the target listener gets a new accept-queue entry via
inet_csk_reqsk_queue_add(), but that path never notifies the target
listener's waiters. A nonblocking accept() still works because it
checks the queue directly, but poll()/epoll_wait() waiters and
blocking accept() callers can also remain asleep indefinitely.
Call READ_ONCE(nsk->sk_data_ready)(nsk) after a successful migration
in inet_csk_listen_stop().
However, after inet_csk_reqsk_queue_add() succeeds, the ref acquired
in reuseport_migrate_sock() is effectively transferred to
nreq->rsk_listener. Another CPU can then dequeue nreq via accept()
or listener shutdown, hit reqsk_put(), and drop that listener ref.
Since listeners are SOCK_RCU_FREE, wrap the post-queue_add()
dereferences of nsk in rcu_read_lock()/rcu_read_unlock(), which also
covers the existing sock_net(nsk) access in that path.
The reqsk_timer_handler() path does not need the same changes for two
reasons: half-open requests become readable only after the final ACK,
where tcp_child_process() already wakes the listener; and once nreq is
visible via inet_ehash_insert(), the success path no longer touches
nsk directly. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix re-decryption of RESPONSE packets
If a RESPONSE packet gets a temporary failure during processing, it may end
up in a partially decrypted state - and then get requeued for a retry.
Fix this by just discarding the packet; we will send another CHALLENGE
packet and thereby elicit a further response. Similarly, discard an
incoming CHALLENGE packet if we get an error whilst generating a RESPONSE;
the server will send another CHALLENGE. |
