| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
tty: port: fix tty_port_tty_vhangup() race
Drivers rely on tty_port_tty_vhangup() to synchronously hang up their
ports before tearing down resources as part of deregistration (e.g. on
physical disconnect).
If tty_port_tty_vhangup() races with another hangup it may however
return before the port has been shut down. This is in turn can lead to
use-after-free and NULL-pointer dereferences in racing ioctls (including
a synchronous hangup) and in processing of racing asynchronous hangups
(carrier loss).
Add the missing serialisation to tty_port_tty_vhangup() and
tty_port_hangup() so that the former does not return until the port has
been shut down also when there is a racing hangup.
Note that serial core does not use tty_port_hangup(), but it already
holds the port mutex when clearing port->tty and shutting down the port
in uart_hangup(). |
| In the Linux kernel, the following vulnerability has been resolved:
tty: abort break signalling on hangup
The break ioctls can race with hangup and end up calling into a tty
driver for a device that is already gone or powered down.
Drivers must handle this race, but TCSBRK and TCSBRKP should still be
aborted to avoid calling back into the driver after a user-controlled
timeout (possibly even after the tty has been reopened).
Note that drivers should disable any break state on shutdown so just
return on hangup (calling break_ctl() again is racy and will most likely
fail for drivers handling the race). |
| In the Linux kernel, the following vulnerability has been resolved:
tty: fix saved termios reset race
Resetting saved termios state on device registration is needed where a
minor number can be reused for an entirely different device and where
the old settings may prevent the port from even being opened (e.g. when
CLOCAL is not set).
Not all TTY drivers guarantee that the minor number is no longer in use
when registering devices however, something which can lead to a
use-after-free when closing a TTY (and saving its termios) races with
re-registration.
Add a new TTY_DRIVER_RESET_SAVED_TERMIOS flag to request that any saved
termios state is reset on registration and only set it for drivers that
make sure that the minor number is no longer in use. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: max3100: shut down timer before freeing port
max3100_shutdown() stops the polling timer but returns early during
system suspend. If the SPI device is unbound before resume, the serial
core does not call max3100_shutdown() again, so max3100_remove() frees
the port while the timer remains armed. max3100_timeout() may then
access the freed port and re-arm the timer.
Add final timer teardown to max3100_remove() and use
timer_shutdown_sync() to prevent a racing callback from re-arming it.
Also free the IRQ and destroy the workqueue there before freeing the
port. Keep timer_delete_sync() in max3100_shutdown() so that a
subsequent open() can re-arm the timer.
The workqueue is created before request_irq() and destroyed on both
request_irq() failure and normal shutdown. Its presence at remove thus
identifies the IRQ left registered when suspend bypasses shutdown.
Free the IRQ before destroying the workqueue, in both
max3100_shutdown() and max3100_remove(), and cancel the pending work
in between. free_irq() waits for a running interrupt handler to
finish and no new handler can start afterwards, so a racing handler
cannot queue work on a workqueue that is being destroyed; the
force_end_work check in max3100_dowork() only narrows that window, as
a handler delayed between the check and queue_work() could still run
after the teardown has cleared the workqueue pointer. Cancelling the
work also keeps destroy_workqueue() from waiting on a queued work item
in case remove() ever runs while the freezable workqueue is still
frozen, e.g. device removal during the resume window, before
workqueues are thawed.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_bcm7271: fix use-after-free in brcmuart_remove()
brcmuart_handle_irq() starts priv->hrt to work around a receive-timeout
quirk of the 8250 core when hardware flow control is enabled; the timer
callback brcmuart_hrtimer_func() dereferences priv.
brcmuart_remove() cancels the hrtimer before it unregisters the port, so
a receive-timeout interrupt that arrives in between re-arms the timer.
After devm frees priv, the callback runs on freed memory.
Unregister the port before cancelling the hrtimer.
serial8250_unregister_port() shuts the port down and frees its IRQ, so
brcmuart_handle_irq() can no longer restart the timer, and the final
hrtimer_cancel() drains any timer that was armed before or during the
unregister.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: Serialize compat port-info ioctls
The native sequencer ioctl path serializes handler calls with
client->ioctl_mutex, but the translated port-info compat path invokes the
same handlers through snd_seq_kernel_client_ctl() without taking that
mutex.
This lets concurrent compat CREATE_PORT requests pass the port-count
check before any request reaches the serialized insertion. The computed
integer port index can then exceed the address field range and wrap to an
existing index. Subsequent subscriber teardown can resolve the duplicate
address to the wrong port and access a freed subscriber.
Take ioctl_mutex while dispatching converted port-info requests, matching
the native ioctl path. All translated port-info commands share this
helper, so their accesses to the client port state are serialized as
well. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: Fix initial port reference race
For RFCOMM_RELEASE_ONHUP devices, rfcomm_tty_install() and
__rfcomm_release_dev() both use RFCOMM_TTY_OWNED to decide who drops the
initial tty_port reference. The release path tests the bit separately
from the install path setting it, so both can drop that reference.
The synchronous hangup does not prevent this race: port->tty is not
assigned until tty_port_open(), after installation. The following
interleaving is possible:
1. Install and release each obtain a reference with rfcomm_dev_get().
2. Release observes RFCOMM_TTY_OWNED clear.
3. Install sets RFCOMM_TTY_OWNED and drops the initial reference.
4. Release drops the same initial reference again.
5. TTY cleanup drops its reference and frees the device.
6. Release performs its final tty_port_put() on the freed port.
KASAN reported:
BUG: KASAN: slab-use-after-free in tty_port_put+0x22/0x190
Write of size 4 at addr ffff8881001d3d5c by task poc/92
Call Trace:
tty_port_put+0x22/0x190
rfcomm_dev_ioctl+0x1d4/0x1930
sock_do_ioctl+0x110/0x260
sock_ioctl+0x380/0x590
__x64_sys_ioctl+0x134/0x1c0
Allocated by task 88:
rfcomm_dev_ioctl+0x8f6/0x1930
sock_do_ioctl+0x110/0x260
sock_ioctl+0x380/0x590
__x64_sys_ioctl+0x134/0x1c0
Freed by task 65:
kfree+0x131/0x3c0
rfcomm_dev_destruct+0x23b/0x2f0
release_one_tty+0xc1/0x370
process_one_work+0x661/0x1090
Use test_and_set_bit() in both paths so that only the caller that changes
RFCOMM_TTY_OWNED from clear to set drops the initial reference. Each path
keeps its own lookup reference until release or TTY cleanup, preserving
the existing callback ordering and error handling. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Serialize SMP remote OOB data access
build_pairing_cmd() looks up remote OOB data and copies its contents
without holding hdev->lock, which serializes the list's writers. After
SMP finds an entry, a concurrent management Remove Remote OOB Data
command can unlink and free it before SMP reads its present flag or
copies its random and confirmation values. Removal can also invalidate
an entry while the lookup is still traversing the list.
KASAN reported:
BUG: KASAN: slab-use-after-free in build_pairing_cmd+0x948/0x9b0
Call Trace:
build_pairing_cmd+0x948/0x9b0
smp_recv_cb+0x459f/0x8110
l2cap_recv_frame+0xf14/0x9190
l2cap_recv_acldata+0xa64/0xd40
hci_rx_work+0x4ca/0x730
Allocated by task 87:
hci_add_remote_oob_data+0x11d/0x530
add_remote_oob_data+0x282/0x400
hci_sock_sendmsg+0x1033/0x1ea0
Freed by task 93:
hci_remote_oob_data_clear+0x108/0x1c0
remove_remote_oob_data+0x198/0x220
hci_sock_sendmsg+0x1033/0x1ea0
Taking hdev->lock in build_pairing_cmd() would recurse for callers that
already hold it and invert the device-to-L2CAP lock order on the receive
path. Add a per-device remote_oob_lock instead, held across the SMP
lookup and copies and by the add, remove and clear helpers. Cover
initialization and in-place updates as well, so SMP cannot read partially
initialized or updated OOB values. Release the mutex on allocation
failure, preserving the existing error return.
The new critical sections acquire no device, connection or channel locks.
Writers retain their existing hdev->lock protection, which continues to
serialize the other readers without changing their locking or behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Fix inquiry cache use-after-free
The sync command worker holds hdev->req_lock, but inquiry-cache updates
and flushes use hdev->lock. Both hci_acl_create_conn_sync() and
hci_stop_discovery_sync() look up entries and read their fields without
taking hdev->lock.
After either lookup returns, a concurrent HCIINQUIRY ioctl can acquire
hdev->lock and flush the cache, freeing the entry. The worker then reads
the freed entry while preparing a create-connection or remote-name-cancel
command. The list traversal also races with cache updates and removal.
KASAN reported these accesses:
BUG: KASAN: slab-use-after-free in hci_acl_create_conn_sync+0x5f1/0x650
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_acl_create_conn_sync+0x5f1/0x650
hci_cmd_sync_work+0x13c/0x290
Allocated by task 90:
hci_inquiry_cache_update+0x3e6/0x7d0
hci_inquiry_result_evt+0x3cb/0x560
Freed by task 93:
hci_inquiry_cache_flush+0x111/0x2b0
hci_inquiry+0x2f2/0x780
hci_sock_ioctl+0x269/0x5f0
BUG: KASAN: slab-use-after-free in hci_stop_discovery_sync+0x3b1/0x3c0
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_stop_discovery_sync+0x3b1/0x3c0
hci_cmd_sync_work+0x173/0x300
Allocated by task 86:
hci_inquiry_cache_update+0x483/0x940
hci_inquiry_result_evt+0x3cb/0x560
Freed by task 91:
hci_inquiry_cache_flush+0x13e/0x2f0
hci_inquiry+0x2f2/0x780
hci_sock_ioctl+0x269/0x5f0
Hold hdev->lock across each lookup and all reads from its result. Copy the
remote address before unlocking so discovery cancellation does not retain
a cache entry pointer. Release the lock before sending synchronous HCI
commands, since their completion handlers may need the same lock. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_conn: Lock parent access during enhanced SCO setup
Bluetooth: hci_conn: Lock parent access during enhanced SCO setup
hci_enhanced_setup_sync() runs on the request workqueue without the
hci_dev_lock held by its caller when setup was queued. Its CVSD
capability check and find_next_esco_param() dereference conn->parent
while the receive workqueue can unlink and release that parent.
The following interleaving can cause a use-after-free:
hci_enhanced_setup_sync() hci_disconn_complete_evt()
load conn->parent
hci_dev_lock()
hci_conn_del(ACL parent)
unlink SCO child
drop link's parent reference
clear child->parent
release ACL parent
bt_link_release()
kfree(parent)
hci_dev_unlock()
read parent->features[0][3]
The reference held for the queued SCO child does not keep its ACL parent
alive after unlinking. Commit 42de40abe25d ("Bluetooth: hci_conn: fix the
SCO setup context lifetime") protects the child stored in the queued
context, but leaves these parent accesses unprotected.
With a 40 ms diagnostic delay after loading conn->parent, an instrumented
kernel based on fd179f8a05be, which already contains 42de40abe25d,
BUG: KASAN: slab-use-after-free in hci_enhanced_setup_sync+0xda5/0xdf0
Read of size 1 at addr ffff888102204047 by task kworker/u17:0/93
Call Trace:
hci_enhanced_setup_sync+0xda5/0xdf0
hci_cmd_sync_work+0x13c/0x290
process_one_work+0x6b4/0x10e0
Allocated by task 92:
__hci_conn_add+0x304/0x1df0
hci_connect_acl+0x349/0x3e0
hci_connect_sco+0x3b/0x9a0
sco_sock_connect+0x475/0xca0
Freed by task 94:
kfree+0x121/0x3c0
bt_link_release+0x79/0xa0
device_release+0xc8/0x240
kobject_put+0x14d/0x280
hci_conn_del+0x524/0xe30
hci_disconn_complete_evt+0x403/0x8c0
hci_event_packet+0x71b/0xb20
hci_rx_work+0x293/0x730
The accessed address is 71 bytes into the freed ACL parent, at its
features[0][3] byte; the queued SCO child is a different object. The
diagnostic preserves the loaded parent across the delay, matching the
unmodified compiled capability check, and does not change the parent
references or teardown path.
Hold hci_dev_lock() across the codec switch, including every call to
find_next_esco_param(), and release it on all selection errors. Keep
configure_datapath_sync() outside the critical section because it waits
for HCI events. Preserve parameter selection and existing return values. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Serialize ACL scheduling with channel deletion
hci_chan_sent() selects a channel under RCU but drops the read lock before
accessing chan->conn and returning the channel. The ACL and LE schedulers
then use its packet queue and update its transmit counters without any
protection against channel deletion.
After TX selects a channel and releases RCU, a disconnect command timeout
on the separate request workqueue can run hci_conn_failed() and
l2cap_conn_del(). hci_chan_del() can then unlink the channel, complete
synchronize_rcu(), purge its queue and free it before TX resumes. This
causes use-after-free both in hci_chan_sent() and in its callers.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_chan_sent+0x892/0x9b0
Workqueue: hci0 hci_tx_work
Call Trace:
hci_chan_sent+0x892/0x9b0
hci_tx_work+0x5e6/0xb70
Allocated by task 91:
hci_chan_create+0xe3/0x350
l2cap_conn_add.part.0+0x12/0xa30
l2cap_chan_connect+0x110d/0x1b60
l2cap_sock_connect+0x310/0x530
Freed by task 99:
hci_chan_del+0x11f/0x170
l2cap_conn_del+0x4f1/0x800
l2cap_connect_cfm+0x88c/0xd30
hci_conn_failed+0x150/0x250
hci_abort_conn_sync+0x3e3/0x800
hci_cmd_sync_run+0x7e/0xc0
hci_abort_conn+0x105/0x1f0
disconnect_sync+0x157/0x290
hci_cmd_sync_work+0x13c/0x290
Hold the existing device mutex across channel selection and transmission
in both schedulers to serialize them with channel teardown. Keep timeout
handling outside the critical sections because hci_link_tx_to() acquires
the same mutex. This also permits the transmit path to sleep, unlike
extending the RCU read-side critical section across packet submission. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Serialize fragmented ISO packet queueing
The fragmented path in hci_queue_iso() calls __skb_queue_tail() without
holding conn->data_q.lock. The socket lock serializes senders, but the
transmit worker can concurrently remove packets from this queue using
skb_dequeue().
After an insertion saves the old tail pointer, hci_sched_iso() can dequeue
that packet and pass it to the driver. The driver can free the packet
before the insertion resumes and writes to the old tail's next pointer,
causing a use-after-free. Concurrent updates can also corrupt the queue.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_send_iso+0xc7d/0xe10
Call Trace:
hci_send_iso+0xc7d/0xe10
iso_sock_sendmsg+0x710/0x900
__sys_sendto+0x34a/0x3a0
Allocated by task 86:
__alloc_skb+0xdd/0x820
alloc_skb_with_frags+0x7e/0x770
sock_alloc_send_pskb+0x67a/0x820
bt_skb_sendmsg.constprop.0+0xc0/0x6c0
iso_sock_sendmsg+0x44e/0x900
Freed by task 90:
kmem_cache_free+0xcb/0x3d0
vhci_read+0x33f/0x4d0
vfs_read+0x177/0xa20
Hold the queue lock across the entire fragment batch, as hci_queue_acl()
does, to serialize insertion against dequeue while preserving fragment
ordering. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: keep paired old chanctx alive
An in-place replacement keeps reciprocal replace_ctx pointers between
the old WILL_BE_REPLACED chanctx and the new REPLACES_OTHER chanctx.
However, the early free paths only consider assigned and reserved link
users when deciding whether to free the old chanctx.
That lets the old chanctx be freed too early while the replacement
partner still points back to it, either when the last assigned link is
released or when that link successfully reassigns to another existing
context. Later unreserve and switch-finalization paths can then follow a
stale replace_ctx pointer.
Keep a paired old chanctx alive until the replacement pair has been torn
down. Apply the same check to both __ieee80211_link_release_channel()
and ieee80211_link_use_reserved_reassign(). If the replacement is later
abandoned, ieee80211_link_unreserve_chanctx() already tears down the
pairing before freeing the old chanctx once no users remain. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: fix driver deregistration order
USB serial driver modules register one driver for the USB bus and one or
more drivers for the ports on the USB serial bus.
When unloading a driver module, the USB driver must be deregistered
before the USB serial bus drivers so that I/O is stopped before
unbinding the ports to avoid use-after-free in completion handlers
accessing port data.
Note that the "new_id" attributes must first be removed to prevent new
ids from being added and triggering a probe of the USB driver after it
has been deregistered. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: light: gp2ap020a00f: drain irq_work after free_irq
The threaded IRQ handler queues data->work through irq_work_queue() so
the trigger is polled from a per-CPU context. free_irq() does not flush
an irq_work the handler already queued, so after gp2ap020a00f_remove()
returns that work may still run and call iio_trigger_poll() on data->trig,
which the devm cleanup has already freed, causing a use-after-free.
Add irq_work_sync(&data->work) after free_irq() in remove() and in the
probe error path, mirroring commit 78601726d4a5 ("iio: trigger: sysfs:
fix use-after-free on remove").
Found by an in-house static analysis tool, confirmed by manual review. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/nouveau/uvmm: fix UAF in nouveau_uvmm_sm when BO is in TTM_PL_SYSTEM
nouveau_uvmm_sm() calls op_map(), which passes bo->resource through
nouveau_mem() to nouveau_uvma_map(). nouveau_uvmm_vmm_map() then reads
mem->mem.type.
But this is only valid when bo->resource is backed by struct nouveau_mem,
as is the case for VRAM and TT resources. If the BO is left in
TTM_PL_SYSTEM, bo->resource is only a struct ttm_resource. Treating it
as struct nouveau_mem makes the mem->mem.type read past the end of the
resource, causing a KASAN: slab-use-after-free Read in nouveau_uvmm_sm
report:
BUG: KASAN: slab-use-after-free in nouveau_uvmm_vmm_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:152 [inline]
BUG: KASAN: slab-use-after-free in nouveau_uvma_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:199 [inline]
BUG: KASAN: slab-use-after-free in op_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:849 [inline]
BUG: KASAN: slab-use-after-free in nouveau_uvmm_sm.constprop.0+0x6ab/0x900 drivers/gpu/drm/nouveau/nouveau_uvmm.c:903
Read of size 1 at addr ffff888127d3e3a0 by task kworker/0:1/11
CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 7.2.0 #5 PREEMPT(lazy)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: nouveau_sched_wq_2224 drm_sched_run_job_work
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x95/0xe0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xcb/0x5a0 mm/kasan/report.c:482
kasan_report+0xca/0x100 mm/kasan/report.c:595
nouveau_uvmm_vmm_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:152 [inline]
nouveau_uvma_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:199 [inline]
op_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:849 [inline]
nouveau_uvmm_sm.constprop.0+0x6ab/0x900 drivers/gpu/drm/nouveau/nouveau_uvmm.c:903
nouveau_uvmm_sm_unmap drivers/gpu/drm/nouveau/nouveau_uvmm.c:932 [inline]
nouveau_uvmm_bind_job_run+0xd6/0x250 drivers/gpu/drm/nouveau/nouveau_uvmm.c:1532
nouveau_job_run drivers/gpu/drm/nouveau/nouveau_sched.c:350 [inline]
nouveau_sched_run_job+0x62/0xd0 drivers/gpu/drm/nouveau/nouveau_sched.c:364
drm_sched_run_job_work+0x356/0xa10 drivers/gpu/drm/scheduler/sched_main.c:1061
process_one_work+0x8a5/0x1900 kernel/workqueue.c:3322
process_scheduled_works kernel/workqueue.c:3405 [inline]
worker_thread+0x5dd/0xd80 kernel/workqueue.c:3486
kthread+0x31d/0x420 kernel/kthread.c:436
ret_from_fork+0x662/0x940 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
Allocated by task 2224 on cpu 0 at 66.550027s:
kasan_save_stack+0x24/0x50 mm/kasan/common.c:57
kasan_save_track+0x17/0x60 mm/kasan/common.c:78
poison_kmalloc_redzone mm/kasan/common.c:398 [inline]
__kasan_kmalloc+0xaa/0xb0 mm/kasan/common.c:415
kasan_kmalloc include/linux/kasan.h:263 [inline]
__do_kmalloc_node mm/slub.c:5334 [inline]
__kmalloc_noprof+0x304/0x7c0 mm/slub.c:5359
_kmalloc_noprof include/linux/slab.h:992 [inline]
dma_resv_list_alloc+0x27/0x90 drivers/dma-buf/dma-resv.c:106
dma_resv_reserve_fences+0x60e/0xa30 drivers/dma-buf/dma-resv.c:205
ttm_bo_alloc_resource+0x12c/0xbd0 drivers/gpu/drm/ttm/ttm_bo.c:721
ttm_bo_validate+0x1bc/0x4a0 drivers/gpu/drm/ttm/ttm_bo.c:856
ttm_bo_init_reserved+0x2c3/0x570 drivers/gpu/drm/ttm/ttm_bo.c:970
nouveau_bo_init+0x159/0x2c0 drivers/gpu/drm/nouveau/nouveau_bo.c:359
nouveau_gem_new+0x234/0x5f0 drivers/gpu/drm/nouveau/nouveau_gem.c:272
nouveau_gem_ioctl_new+0x1eb/0x420 drivers/gpu/drm/nouveau/nouveau_gem.c:352
drm_ioctl_kernel+0x192/0x350 drivers/gpu/drm/drm_ioctl.c:817
drm_ioctl+0x4f8/0xb40 drivers/gpu/drm/drm_ioctl.c:914
nouveau_drm_ioctl+0xea/0x2c0 drivers/gpu/drm/nouveau/nouveau_drm.c:1338
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl fs/ioctl.c:583 [inline]
__x64_sys_ioctl+0x180/0x1d0 fs/ioctl.c:583
do_syscall_x64 ar
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: mcast: use rcu_assign_pointer() for __rcu list updates
Several places in net/ipv6/mcast.c update RCU-protected lists
(np->ipv6_mc_list, idev->mc_list, idev->mc_tomb) using direct pointer
assignments instead of rcu_assign_pointer():
1. In __ipv6_dev_mc_dec(), unlinking a group from idev->mc_list did:
*map = ma->next;
without rcu_assign_pointer() while concurrent readers traverse
idev->mc_list locklessly under rcu_read_lock().
2. In ipv6_sock_mc_drop() and __ipv6_sock_mc_close(), unlinking a group
from np->ipv6_mc_list directly assigned *lnk = mc_lst->next and
np->ipv6_mc_list = mc_lst->next without rcu_assign_pointer(), racing
with lockless readers in inet6_mc_check().
3. In __ipv6_sock_mc_join(), mc_lst->next was initialized to
np->ipv6_mc_list via raw assignment before publishing mc_lst.
4. In mld_del_delrec() and __ipv6_dev_mc_inc(), __rcu source pointers
passed into rcu_assign_pointer() lacked explicit dereference helpers.
Fix these by consistently using rcu_assign_pointer() along with
mc_dereference() / sock_dereference(). |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btqcomsmd: destroy RPMsg endpoints before freeing hci_dev
The command and ACL RPMsg endpoints store struct btqcomsmd as their
callback private data. The receive callbacks dereference btq->hdev
without taking an hci_dev reference.
The current teardown order frees the hci_dev before destroying the RPMsg
endpoints in both the hci_register_dev() error path and the driver remove
path. If WCNSS delivers data in that window, the endpoint callback can
run with an already freed hci_dev and pass it to the Bluetooth core.
For qcom_smd endpoints, rpmsg_destroy_ept() closes the channel and clears
the callback under the channel recv_lock. The receive path holds the same
lock while invoking the callback, so destroying the endpoints first both
prevents new callbacks and serializes with any callback already running.
Destroy the command and ACL endpoints before hci_free_dev(). Keep
hci_unregister_dev() first during remove so the HCI core stops issuing
operations before the transport endpoints are shut down. In the full
registration-error cleanup path, return directly after freeing the hci_dev
to avoid falling through to the partial-construction labels and destroying
the endpoints twice. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: cttimeout: prevent UAF during module unload
nf_ct_set_timeout() protects the timeout hook dereference and policy lookup
with rcu_read_lock(). cttimeout_exit(), however, unregisters the per-net
operations before it clears the hook.
This allows the following interleaving:
CPU 0 CPU 1
cttimeout_exit() nf_ct_set_timeout()
unregister_pernet_subsys() rcu_read_lock()
kfree(pernet) h = nf_ct_timeout_hook
h->timeout_find_get()
nfct_timeout_pernet()
The hook still points to ctnl_timeout_find_get() when CPU 1 looks up the
already freed per-net timeout list. KASAN reported:
BUG: KASAN: slab-use-after-free in ctnl_timeout_find_get
Read of size 8 by task poc/90
Call Trace:
ctnl_timeout_find_get+0x271/0x2a0 [nfnetlink_cttimeout]
nf_ct_set_timeout+0x7b/0x3c0
xt_ct_tg_check+0x724/0xb20
xt_check_target+0x234/0xa90
do_ipt_set_ctl+0x570/0x1270
Allocated by task 89:
__kmalloc_noprof+0x16e/0x460
ops_init+0x6d/0x420
register_pernet_operations+0x2f6/0x670
Freed by task 91:
kfree+0x131/0x390
ops_undo_list+0x3d4/0x730
unregister_pernet_operations+0x232/0x490
unregister_pernet_subsys+0x1c/0x30
cttimeout_exit+0x52/0x970 [nfnetlink_cttimeout]
Clear the hook and wait for existing readers before unregistering the
per-net operations. This blocks new policy lookups and ensures readers that
observed the hook finish before the per-net storage is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Skip vport under deletion in report ID acquisition
qla24xx_report_id_acquisition() format-1 handling walks ha->vp_list under
vport_slock, takes a vref_count on the matching vport and calls
qla_update_host_map() to register its port id.
A vport teardown via qla24xx_vport_delete() sets VPORT_DELETE, then
qla24xx_disable_vp() removes the vport from the host_map btree and zeroes
vha->d_id (RESET_AL_PA). The vport is only unlinked from vp_list later,
in qla24xx_deallocate_vp_id(), which clears vp_map[idx] (RESET_VP_IDX)
but does not touch host_map. In the window in between, report ID
acquisition can still find the vport on vp_list and call
qla_update_host_map(); with d_id already zeroed it takes the
btree_insert32() path and re-inserts the dying vport into host_map.
Nothing cleans that entry afterwards, so once scsi_host_put() frees the
vha a later host_map lookup dereferences freed memory.
Skip a vport that has VPORT_DELETE set before taking the reference, so it
is neither re-registered nor scheduled for DPC re-registration. This
mirrors the existing guard in qla2x00_alert_all_vps(). |
